Bending System Stirrups/Anchors

System anchors are connecting elements. In the Anchor Lamination/Prepreg Technique and the Joint Lamination/Prepreg Technique, they are embedded into the laminate. When producing a custom-made orthosis, it is necessary to adapt the system stirrups and anchors. Depending on the material, a defined bending radius should be observed during bending in order to ensure stability.

You can find the bending radii for system stirrups and anchors in different materials in the manual System Side Bars and System Anchors

Bending the System Stirrups/Anchors

Step 1/11

First, mark the lower edge of the assembly/lamination dummy on the system stirrup. Everything above this line must not be bent, as this area (the joint area) is a part of the system joint later.
Note: When you have acquired a bent system stirrup, you can skip the steps 1 to 4.

Step 2/11

Clamp the system stirrup into a vice with plain jaws to bend it. Pay attention to the marking to avoid a subsequent deformation of the joint areas and to be able to bend very close to the joint.
Note: When you have acquired a bent system stirrup, you can skip the steps 1 to 4.

Step 3/11

Adapt the system stirrup to the shape of the model. Bend the system stirrup neck with a bending iron. Only bend in one direction. Note: Do not use a hammer and do not heat the material.
Note: When you have acquired a bent system stirrup, you can skip the steps 1 to 4.

Step 4/11

Remove the system stirrup from the vice and check the distance from the system stirrup to the model.
Note: When you have acquired a bent system stirrup, you can skip the steps 1 to 4.

Step 5/11

Adapt the system stirrup to the shape of the model. Bend the lower part of the system stirrup with a bending iron. Only bend in one direction.
Note: Do not use a hammer and do not heat the material.
Check if there is enough space left for the reinforcement layers between system stirrup and model.

Step 6/11

Adapt the system stirrup to the shape of the model. Bend the system stirrup foot with a bending iron. Only bend in one direction.
Note: Do not use a hammer and do not heat the material. 
Check if there is enough space left for the reinforcement layers between system stirrup and model.

Step 7/11

Press the system anchor to the joint’s upper part by using a washer and a screw. To do so, use a torque screwdriver and a torque of 6 Nm. Then, remove washer and screw again.

Step 8/11

Fix the system anchor with the screw (farther away from the joint) at the joint's upper part before you begin bending.

Step 9/11

While bending, please consider the applicable bending radii and use a bending iron with round edges.
Note: You will find information on bending radii and the tools to be used in the manual for System Side Bars and System Anchors.

Step 10/11

Check the distance from system anchor and stirrup to the positive cast. Please make sure to have enough space left for the reinforcing profile and the reinforcement layers in order to avoid later strains to the laminate. Thus, the joint areas stay parallel.

Step 11/11

Grind the system stirrup and the system anchor. Always grind in direction of rolling. Remove all notches from bending and avoid sharp edges.
Note: System ankle joints with dorsiflexion stop, which can be adjusted by filing, should always be mounted in their pre-assembled neutral position without changing the dorsiflexion stop.


×

Technische Cookies

Name Purpose Record Duration Provider Type
fe_typo_user This cookie is a standard session cookie of TYPO3. It stores the entered access data when a user logs in for a closed area. duration of the session TYPO3 Association, Sihlbruggstrasse 105, 6340 Baar, Schweiz HTTP
rc::c distinguishes between humans and bots duration of the session Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland HTML
×

Marketing Cookies

Name Purpose Record Duration Provider Type
_ga registers a unique ID which is used to generate statistical data on the user’s website usage 2 years Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland HTTP
_gid registers a unique ID which is used to generate statistical data on the user’s website usage 1 day Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland HTTP
_gat The _gat_UA cookie also contains the identity number (_gat_ <***>) of the Google Analytics account or website to which the cookie refers.  1 day Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland HTTP
_gcl_au is used by Google AdSense for advertising efficiency on web pages 3 months Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland HTTP
r/collect transmits data about the user’s device and behaviour to Google Analytics duration of the session Google Ireland Limited, Google Building Gordon House, 4 Barrow St, Dublin, D04 E5W5, Irland Pixel